Bambu Lab P2S: Difference between revisions

Revision as of 06:38, 23 March 2026

Sources and Inspiration

The following settings have been optimized for a BambuLab P2S. These settings and tweaks are based on the work of HoHansen, Timnolte, BlockBadger, Painted4Combat, ObscuraNoc and many more. At this point - Thank you for your work. If you like to read more about their specific settings, I linked to their posts at the end of this page.

Disclaimer: Please always check and verify before printing if the settings are applicable for your setup, printer, filament and environment.

Requirements for these settings

The nozzle is a stainless steel 0.2mm from BambuLab
The filament is SUNLU PLA+ 2.0 in the color bone white. Other colors might work as well.
OrcaSlicer (this guide is written based on 2.3.2-rc2)
Textured PEI Plate. Another will work as well but you will need to tweak your brim settings, temperature and cooling.

Settings

The settings are split up into the following section:

Baseline - How to start
Printer - Specific settings for the printer to made.
Filament - Configuration for the SUNLU PLA+ 2.0 filament.
Process - Printing profile.

Moreover, there exist V1 and V2 settings. The current used are the V2 settings. The V1 settings are for kept as an archive. Every setting is listed as a screenshot taken from OrcaSlicer.

Baseline

In the process tab on the left side you need to switch "Show/Hide advanced paramters" to on (the symbol that looks like a drawing of an atom). Otherwise some settings will be hidden.

Start with a standard profile of the P2S and set it to 0.2mm nozzle, the according build plate and the filament type. Then set your base process settings to 0.08mm layer height. This is your baseline for the following configuration, since we will only touch certain values and leave the rest as configured in the standard profile of the 0.08mm layer height.

Fixing Adhesion (optional, is NOT used for V2 settings)

In addition, this modification might help with adhension https://makerworld.com/de/models/1926190-p2s-auxiliary-fan-diffuser#profileId-2464793 which is recommended to print from ASA to be used in higher temperature environments. It was used for the V1 settings, but I removed it for the V2 settings for an optimized cooling.

Printer

Filament

V2 settings in progress, following soon.

Process

Quality Settings

V2 settings in progress, following soon.

Strength

V2 settings in progress, following soon.

Speed

V2 settings in progress, following soon.

Support

Bambu Lab P2S Support Settings

Multimaterial

V2 settings in progress, following soon.

Others

V2 settings in progress, following soon.

Special Thanks

I like to give my credits and thanks to the people how directly or indirectly helped to create this profile for the P2S. TimNolte & BlockBadger on the OPR Discord server, to mention two of them, but there are many other in chat that contributed. Thank you for the ongoing feedback, tips and tweaks.

Additionally, the settings are based on the following other available profiles:

@@ Line 18: / Line 18: @@
 * Filament - Configuration for the SUNLU PLA+ 2.0 filament.
 * Process - Printing profile.
+Moreover, there exist V1 and V2 settings. The current used are the V2 settings. The V1 settings are for kept as an archive. Every setting is listed as a screenshot taken from OrcaSlicer.
-Every setting is listed as a screenshot taken from OrcaSlicer.
 ===== Baseline =====
@@ Line 28: / Line 27: @@
 Start with a standard profile of the P2S and set it to 0.2mm nozzle, the according build plate and the filament type. Then set your base process settings to 0.08mm layer height. This is your baseline for the following configuration, since we will only touch certain values and leave the rest as configured in the standard profile of the 0.08mm layer height.
-In addition, this modification might help with adhension https://makerworld.com/de/models/1926190-p2s-auxiliary-fan-diffuser#profileId-2464793  which is recommended to print from ASA to be used in higher temperature environments.
+===== Fixing Adhesion (optional, is NOT used for V2 settings) =====
+In addition, this modification might help with adhension https://makerworld.com/de/models/1926190-p2s-auxiliary-fan-diffuser#profileId-2464793  which is recommended to print from ASA to be used in higher temperature environments. It was used for the V1 settings, but I removed it for the V2 settings for an optimized cooling.
 ===== Printer =====
@@ Line 34: / Line 34: @@
 ===== Filament =====
-[[File:Filament_Settings.png]]
+[[File:Filament_Settings.png|thumb|V1 Settings Filament]]
+V2 settings in progress, following soon.
-[[File:Filament_Cooling.png|722x722px]]
+[[File:Filament_Cooling.png|thumb|V1 Settings Filament]]
 ===== Process =====
 ====== '''Quality Settings''' ======
-[[File:Q (1).png]]
+[[File:Q_(1).png|thumb|V1 Settings Quality]]
+V2 settings in progress, following soon.
-[[File:Q (2).png]]
+[[File:Q_(2).png|thumb|V1 Settings Quality]]
+[[File:Q_(3).png|thumb|V1 Settings Quality]]
-[[File:Q (3).png]]
+[[File:Q_(4).png|thumb|V1 Settings Quality]]
-[[File:Q (4).png]]
 ====== '''Strength''' ======
-[[File:St (1).png]]
+[[File:St_(1).png|thumb|V1 Settings Strength]]
+V2 settings in progress, following soon.
-[[File:St (2).png]]
+[[File:St_(2).png|thumb|V1 Settings Strength]]
+[[File:St_(3).png|thumb|V1 Settings Strength]]
-[[File:St (3).png]]
 ====== '''Speed''' ======
-[[File:Sp (1).png]]
+[[File:Sp_(1).png|thumb|V1 Settings Speed]]
+V2 settings in progress, following soon.
-[[File:Sp (2).png]]
+[[File:Sp_(2).png|thumb|V1 Settings Strength]]
+[[File:Sp_(3).png|thumb|V1 Settings Speed]]
-[[File:Sp (3).png]]
 ====== '''Support''' ======
@@ Line 67: / Line 63: @@
 ====== '''Multimaterial''' ======
-[[File:M (1).png]]
+[[File:M_(1).png|thumb|V1 Settings Strength]]
+V2 settings in progress, following soon.
 ====== '''Others''' ======
-[[File:O (1).png]]
+[[File:O_(1).png|thumb|V1 Settings Others]]
+V2 settings in progress, following soon.
-[[File:O (2).png]]
+[[File:O_(2).png|thumb|V1 Settings Others]]
 ==== Special Thanks ====