More actions
mNo edit summary |
Adds link to Google Drive orignal source. |
||
| (One intermediate revision by one other user not shown) | |||
| Line 1: | Line 1: | ||
Original Source: https://drive.google.com/drive/folders/1Fbz-A4jdEFay_BhCykqnTrJJIuXGIYn8?usp=sharing | |||
These settings assume that you are using Orcaslicer, which is the recommended slicer for printing miniatures. However since many slicers are forks of one another, you will likely be able to find the same or similar settings in the slicer of your choice. | These settings assume that you are using Orcaslicer, which is the recommended slicer for printing miniatures. However since many slicers are forks of one another, you will likely be able to find the same or similar settings in the slicer of your choice. | ||
| Line 4: | Line 6: | ||
* removed raft | * removed raft | ||
If you use these supports and find something that works better, please add something to the notes for the setting in question or to the discussion page. | If you use these supports and find something that works better, please add something to the notes for the setting in question or to the discussion page. | ||
Latest revision as of 13:54, 7 August 2025
Original Source: https://drive.google.com/drive/folders/1Fbz-A4jdEFay_BhCykqnTrJJIuXGIYn8?usp=sharing
These settings assume that you are using Orcaslicer, which is the recommended slicer for printing miniatures. However since many slicers are forks of one another, you will likely be able to find the same or similar settings in the slicer of your choice.
Changes from previous version:
- removed raft
If you use these supports and find something that works better, please add something to the notes for the setting in question or to the discussion page.
Settings
| Setting Name | Setting Value | Setting Type | Notes |
|---|---|---|---|
| Enable Support | yes | checkbox | |
| Type | Tree (auto) | dropdown | |
| Style | Organic | dropdown | |
| Threshold Angle | 25 | direct entry | |
| Threshold Overlap | 50% | mm or % | |
| First Layer Density | 90% | direct entry | |
| First Layer Expansion | 6 | mm | determines how big of a “brim” each support will have. Can be adjusted based on your printbed adhesion. |
| On Build Plate Only | yes | checkbox | |
| Remove Small Overhangs | yes | checkbox |
| Setting Name | Setting Value | Setting Type | Notes |
|---|---|---|---|
| Raft Layers | 0 | direct entry | Set this to a value greater than 0 to enable raft |
| Setting Name | Setting Value | Setting Type | Notes |
|---|---|---|---|
| Support/Raft Base | Default | dropdown | |
| Support/Raft Inteface | Default | dropdown | |
| Setting Name | Setting Value | Setting Type | Notes |
|---|---|---|---|
| Top Z Distance | 0.2 | mm | |
| Bottom Z Distance | 0.2 | mm | |
| Support Wall Loops | 2 | direct entry | |
| Base Pattern | Hollow | dropdown | |
| Base Pattern Spacing | 2.5 | mm | |
| Pattern Angle | 0 | direct entry (degrees) | |
| Top Interface Layers | 3 | dropdown / direct entry | |
| Bottom Interface Layers | 2 | dropdown / direct entry | |
| Interface Pattern | Concentric | dropdown | |
| Top Interface Spacing | 0.25 | mm | |
| Bottom Interface Spacing | 0.5 | mm | |
| Normal Support Expansion | 0 | mm | |
| Support/Object XY Distance | 0.25 | mm | |
| Support/Object First Layer Gap | 0.2 | mm | |
| Don’t Support Bridges | No | checkbox | |
| Independent Support Layer Height | Yes | checkbox |
| Setting Name | Setting Value | Setting Type | Notes |
|---|---|---|---|
| Tip Diameter | 1 | mm | |
| Tree Support Branch Distance | 1 | mm | |
| Branch Density | 25 | % | |
| Tree Support Branch Diameter | 1 | mm | |
| Branch Diameter Angle | 2 | degrees | |
| Tree Support Branch Angle | 40 | degrees | |
| Preferred Branch Angle | 45 | degrees |