View source for Printing Miniatures/Printing Tips & Guides/Timnolte supports v5

{{DISPLAYTITLE:TimNolte Supports v5}}
{{DISPLAYTITLE:Timnolte supports v5}}
{{DISPLAYTITLE:Timnolte supports v5}}

Original Source: https://drive.google.com/drive/folders/1Fbz-A4jdEFay_BhCykqnTrJJIuXGIYn8?usp=sharing

These settings assume that you are using Orcaslicer, which is the recommended slicer for printing miniatures. However since many slicers are forks of one another, you will likely be able to find the same or similar settings in the slicer of your choice.

Changes from previous version:

* removed raft

If you use these supports and find something that works better, please add something to the notes for the setting in question or to the discussion page.

== Settings ==
{| class="wikitable"
|+Support
!Setting Name
!Setting Value
!Setting Type
!Notes
|-
|Enable Support
|yes
|checkbox
|
|-
|Type
|Tree (auto)
|dropdown
|
|-
|Style
|Organic
|dropdown
|
|-
|Threshold Angle
|25
|direct entry
|
|-
|Threshold Overlap
|50%
|mm or %
|
|-
|First Layer Density
|90%
|direct entry
|
|-
|First Layer Expansion
|6
|mm
|determines how big of a “brim” each support will have. Can be adjusted based on your printbed adhesion.
|-
|On Build Plate Only
|yes
|checkbox
|
|-
|Remove Small Overhangs
|yes
|checkbox
|
|}
{| class="wikitable"
|+Raft
!Setting Name
!Setting Value
!Setting Type
!Notes
|-
|Raft Layers
|0
|direct entry
|Set this to a value greater than 0 to enable raft
|-
|
|
|
|
|-
|
|
|
|
|}
{| class="wikitable"
|+Filament for Supports
!Setting Name
!Setting Value
!Setting Type
!Notes
|-
|Support/Raft Base
|Default
|dropdown
|
|-
|Support/Raft Inteface
|Default
|dropdown
|
|-
|
|
|
|
|}
{| class="wikitable"
|+Advanced
!Setting Name
!Setting Value
!Setting Type
!Notes
|-
|Top Z Distance
|0.2
|mm
|
|-
|Bottom Z Distance
|0.2
|mm
|
|-
|Support Wall Loops
|2
|direct entry
|
|-
|Base Pattern
|Hollow
|dropdown
|
|-
|Base Pattern Spacing
|2.5
|mm
|
|-
|Pattern Angle
|0
|direct entry (degrees)
|
|-
|Top Interface Layers
|3
|dropdown / direct entry
|
|-
|Bottom Interface Layers
|2
|dropdown / direct entry
|
|-
|Interface Pattern
|Concentric
|dropdown
|
|-
|Top Interface Spacing
|0.25
|mm
|
|-
|Bottom Interface Spacing
|0.5
|mm
|
|-
|Normal Support Expansion
|0
|mm
|
|-
|Support/Object XY Distance
|0.25
|mm
|
|-
|Support/Object First Layer Gap
|0.2
|mm
|
|-
|Don’t Support Bridges
|No
|checkbox
|
|-
|Independent Support Layer Height
|Yes
|checkbox
|
|}
{| class="wikitable"
|+Tree Supports
!Setting Name
!Setting Value
!Setting Type
!Notes
|-
|Tip Diameter
|1
|mm
|
|-
|Tree Support Branch Distance
|1
|mm
|
|-
|Branch Density
|25
|%
|
|-
|Tree Support Branch Diameter
|1
|mm
|
|-
|Branch Diameter Angle
|2
|degrees
|
|-
|Tree Support Branch Angle
|40
|degrees
|
|-
|Preferred Branch Angle
|45
|degrees
|
|}
[[Category:Supports]]
[[Category:Miniatures]]